Kyosho Inferno Mp9 Tki3

[matrix]

Anyone running the Kyosho SP Big Shock Pistons 1.2 x 8 hole.

[mp9ebest]

May 4, 2014 8:17:21 GMT superrcracer said:

I'm running Tebos setup. I'm running the blue springs in the front and the orange in the back.

What do you think about Jared Tebos setup

do you like that setup.

[kyoshoracer]

Here a few setup you might want take a look.
www.kyoshoamerica.com/assets/images/setups/2014NatsWarmup%20King.pdf
www.kyoshoamerica.com/assets/images/setups/MP9%20Nats%20Warm%20Up%20Practice%20TEBO%2014.pdf

[skeeter]

I'm running a kyosho mpe tki3 and have upgraded the chassis to a M2C Racing Kyosho Inferno MP9 TKI3 Chassis. This chassis is day and night over the stock chassis. This chassis is machined from 1/8" thick (3.25mm) 7075 aircraft grade material and clear anodized with machined steel skid plate inserts that are recessed into the chassis. These skid plates fit flush to the bottom of the chassis and will not effect the droop settings or cause you to scrub speed on landings.

[kyoshoracer]

May 25, 2014 19:54:56 GMT skeeter said:

I'm running a kyosho mpe tki3 and have upgraded the chassis to a M2C Racing Kyosho Inferno MP9 TKI3 Chassis. This chassis is day and night over the stock chassis. This chassis is machined from 1/8" thick (3.25mm) 7075 aircraft grade material and clear anodized with machined steel skid plate inserts that are recessed into the chassis. These skid plates fit flush to the bottom of the chassis and will not effect the droop settings or cause you to scrub speed on landings.

Is there a difference on how the car handles with the m2c chassis?

[skeeter]

The m2c chassis is machined from 1/8" thick (3.25mm) 7075 aircraft grade material and clear anodized with machined steel skid plate inserts that are recessed into the chassis. The m2c chassis is more durable than the stock chassis.

[nitrodude]

My buddy runs a m2c chassis on his mp9, he says that he does not feel that the car handles differently. If I were you I would give it a try.

[kyoshoracer]

I also think fiorini makes some chassis, has he tried those out?

[djgray15]

What are the track conditions?

[kyoshoracer]

Jun 4, 2014 0:06:50 GMT djgray15 said:

What are the track conditions?

Do you ever run the Orange springs on the back? If so on what track conditions?

[nitrodude]

Jun 4, 2014 0:06:50 GMT djgray15 said:

What are the track conditions?

If you are refering to what conditions my buddy runs that chassis, it is on a low bite rough track. Conditions are similar to that of the Silver State.

[kyoshoracer]

Take a look at this setup by Kanai

[superrcracer]

I have been looking for the euro front shock towers but can't seem to find them. Anyone know where I can buy them?

[rcracer328]

alright guys for those of you wondering when you should run the orange rear springs, i run them on a surface that i am trying to get more traction out of or that the rear end needs to be slightly softer. On high bite i run the light blue springs front and rear and if it gets really high bite i will put a 2.5 sway bar on the front to even the car out some.

[kyoshoracer]

Jun 15, 2014 5:59:33 GMT rcracer328 said:

alright guys for those of you wondering when you should run the orange rear springs, i run them on a surface that i am trying to get more traction out of or that the rear end needs to be slightly softer. On high bite i run the light blue springs front and rear and if it gets really high bite i will put a 2.5 sway bar on the front to even the car out some.

Ok, Ill try out the Orange springs. What pistons is everyone using?